Plumbing 101: A Necessity for Bathtub Installation
Plumbing 101: A Necessity for Bathtub Installation
Blog Article
Every person maintains their own opinion with regards to Tools You Need to Install a New Bathtub .
Mounting a bathtub isn't specifically rocket science, however it does need strong plumbing, carpentry, and often, tiling skills. Changing an old bath tub with a new one is likewise a moderately difficult project. If the old bathtub is conveniently obtainable, the job can relocate immediately; if you have to open up a wall to eliminate the old bathtub and place the brand-new bathtub, the job is a lot harder. In either case, the job is within a residence handyman's skills, although you will require an assistant to vacate the old tub as well as embeded in the brand-new one. Make sure you have qualified yourself for the task as well as fit trying it. As opposed to hiring a professional to take over a halfway-completed job, it is much better to think about utilizing one before you begin. Chances are you might require an expert plumber to make tube connections.
This write-up will certainly assist you install a brand-new bath tub in your washroom if you have currently acquired a brand-new tub as well as do not require to transform the arrangement of your previous water pipes.
Your devices as well as material list must comprise the following:
Preparing for the Installment
First of all, the sustaining framework provided with the bath ought to be fitted (if called for) according to the manufacturer's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is essential to make certain that if the faucet features a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets unit to avoid stress on the bath tub.
Fit the versatile tap adapters to the bottom of the two faucets utilizing 2 nuts as well as olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you utilize every one of the provided washers.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bath need to currently prepare to be suited its last placement.
Removing Old Taps
If you need to replace old faucets with new ones as a part of your installation, then the first thing you need to do is disconnect the water supply. After doing so, switch on the taps to drain any kind of water staying in the system. The process of getting rid of the existing taps can be rather troublesome because of the restricted accessibility that is typically the case.
Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the faucets. Have a towel prepared for the remaining water that will certainly come from the pipes. Once the supply pipes have actually been removed, use the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single faucets from turning throughout this process. When the faucets have been removed, the holes in the bath/basin will need to be cleansed of any kind of old sealing compound.
Before proceeding to fit the new taps, compare the pipe links on the old faucets to the brand-new faucets. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Mounting the Bath tub
Utilizing both wood boards under its feet, place the bathtub in the called for placement. The wooden boards are practical in evenly spreading the weight of the bath tub over the location of the boards as opposed to focusing all the weight onto four little points.
The following goal is to ensure that the bath tub is leveled all round. This can be achieved by examining the spirit level and also changing the feet on the bath tub until the spirit level reviews level.
To mount faucets, fit all-time low of the furthest adaptable faucet port to the proper supply pipe by making a compression sign up with; after that do the exact same for the other tap.
Switch on the water supply and also examine all joints as well as new pipework for leakages and tighten them if essential. Fill up the bathtub as well as likewise examine the overflow outlet and the regular outlet for leaks.
Ultimately, take care of the bathroom paneling as described in the maker's instruction manual. Tiling as well as securing around the bathtub must wait till the bath tub has been made use of at least once as this will certainly resolve it into its last position.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will need a plastic adapter to prevent damages to the string. One end of the port fits on the plastic tail of the tap and also the other end supplies a connection to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly need lowering couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, place the faucet in the installing opening in the bath/basin making certain that the washers remain in area between the faucet and also the sink. Protect the tap in place with the supplier provided backnut. When the faucet is firmly in position, the supply pipelines can be connected to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with typical tap adapters. The previous kind needs to be connected to the tap ends first, tightening up only by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bath satisfies the tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the fitting can move enough to crack an inflexible seal, creating the water to penetrate the wall between the bath as well as the tiling, bring about problems with moisture and also possible leaks to the ceiling listed below.
You can choose from a selection of coloured sealants to assimilate your components and also fittings. They are offered in tubes and also cartridges, as well as can securing voids as much as a size of 3mm (1/8 inch). If you have a bigger space to fill, you can fill it with spins of soaked newspaper or soft rope. Remember to always load the tub with water before sealing, to enable the activity experienced when the tub is in use. The sealer can crack relatively early if you do not think about this movement prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also quickly readily available on the marketplace. It is a good idea to fit the floor tiles making use of water-resistant or water resistant sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I am just very intrigued by How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I'm hoping you enjoyed our blog post. Loved our posting? Please share it. Let other people check it out. We thank you for reading our article about How to Install a Bathtub Yourself.
This Website Report this page